Refrigerator hook up water line, how to install a water line for a refrigerator

Install a new refrigerator water supply line

Leave the excess water line behind the refrigerator. If the model has a dispenser, make sure the water filter is installed, and then dispense one gallon of water before drinking or using any water from the refrigerator. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator.

How to Hook Up a Water Line to a Refrigerator From the Sink

Shut off the water at the valve that controls the cold-water supply pipe to the faucet. Adapt-a-Tees can be used in many situations where you need an extra line. If needed, you can install a booster pump to compensate for low pressure. Connect the Supply Tube to the Refrigerator. This procedure will vary depending on the type of equipment you use, so follow the kit's instructions.

She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Turn the cold water supply valve on beneath the sink. All information included herein is subject to change without notice. Please help us improve by selecting a reason below.

Turn the supply line on once again. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. In the image, hiv personals dating C demonstrates how it will look when installed. This site uses cookies to enhance your web site experience.

HowStuffWorks

The water lines are typically sold in kits and are not included with the refrigerator. How would you like to contact us? Run the new supply tube to the back of the refrigerator.

If you find water drops or a leak in the connection areas, turn off the main water supply. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. Then you'd need to twist the valve until it pierces your water line.

How to Install a Water Line for a Refrigerator

  1. Measure the distance carefully, and buy a supply tube with plenty of length for the job.
  2. Use pliers to untwist the faucet supply line from the cold water supply valve.
  3. Adapt-A-Tees are easy to install, and they provide the extra line you need with the least amount of work.
  4. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher.
  5. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line.
  6. By continuing to browse or use this site, you are agreeing to our use of cookies.

TOH Network

How to Hook Up a Water Line to a Refrigerator From the Sink

This Old House

  • Keep in mind that you will need a compression nut at both ends, and some kits only come with one.
  • An Adapt-a-Tee is an ideal plumbing fitting for this purpose.
  • If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house.
  • Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet.
  • Coil the excess water line behind the refrigerator.
Connect the water supply line to the refrigerator

Or continue shopping on Samsung. If your home doesn't have a water line installed from a previous refrigerator, you will need a water line that can run between the water pipes in your home and your fridge. Wrap the female thread on the opposite end of the adapter with thread-seal tape.

Connect and install the water line to your refrigerator
You are being redirected

The kit provides you with the required parts to hook up a water line to your refrigerator. Either way, we're going to help you get your home water-ready. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. Thread the ferrule from the kit onto the new line.

Tools List for Connecting a Refrigerator Water and Ice Dispenser

How to Hook Up a Water Line to a Refrigerator

The tee adapter connects to the water supply shutoff valve. Turn on the cold water faucet to drain any water left in the supply line. After installation, check the water pressure by dispensing water. Disconnect the Existing Water Line.

Turn the cold water on the supply line clockwise to close it. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Install a new refrigerator water supply line. The valve connected to the right side of the faucet is the cold water supply line. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator.

Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. Check the connections, app and tighten when necessary. Watch for leaks at all the connections.

She attended Tarrant County College and studied English composition. Thank you for visiting Samsung U. Although the braided steel is considerably more expensive, time our the extra strength it provides is well worth the investment. Question about a promotion? Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections.

Insert the new water line into the opening on the tee. Twist the faucet supply line onto the female end of the adapter. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located.

Redirect Notification As of Nov. Plug your refrigerator into the wall. Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place. Find your water supply lines beneath your sink. Learn more about Samsung promotions.

Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Connect the line to the water line connector on the back of the refrigerator. Visit the download center to get a copy. First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Again, the kit's instructions will tell you how to do this.

Tighten the connections slightly if you see a leak. They come in various sizes to suit whatever situation you have. Tighten the connection just slightly more than hand-tight, using pliers.

How to Connect a Refrigerator Water and Ice Dispenser

You can use the water line leftover from your previous refrigerator, or start fresh with a new kit from the hardware store. Push the refrigerator against the wall. As mentioned above, the water supply line is not included with the refrigerator and is typically sold as a kit at your local hardware store if you don't have one already installed in your home.

How to Install a Water Line for a Refrigerator

Please contact us via Live Chat for a faster response. Disconnect the faucet supply tube from the shutoff valve. Ask the Community Browse answers, ask questions and get solutions from other Samsung customers.

She writes mainly home improvement, ce este speed health and travel articles for various online publications. Twist the male end of a quick-tee adapter onto the valve. Thank you for your feedback!

How to Connect a Refrigerator Water and Ice Dispenser
  • How to tell if you're officially dating
  • Free sugar mummy dating sites in usa
  • Sims dating games for guys
  • Job dating pole emploi
  • Russian dating photos daily mail
  • Single black mom dating
  • Free dating couples devotional